Current location：Home > Product > Clean Room Type Actuator > GRC Series > GRC8 > Motor Right Side

Lightweight and Long Lifespan

Body width：82mm

Repeatability：±0.01mm

Horizontal Load：50kg

Vertical Load：15kg

Maximum Speed：1000mm/s

Travel Range：50-1050mm

Set the motor acceleration and deceleration to0.2seconds.

The standard specifications cannot be applied for the use of inverted cranes. If you have any requirements, please contact us by phone or leave a message online.

Delivery time: 7-10 days

PDF

3D download

Cadenas3 Ddownload

Rigid reinforcement of sliding seat

The body and slide are integrally formed, which improves the problem of poor rigidity and reduces the width, making the installation space of the equipment smaller.

Easy maintenance

Both sides of the entire series have external oil injection nozzles that can be directly filled with oil without the need for a cover. Special steel belt tie design can reduce hair and can be used in cleanroom environments.

Assembly, time-saving, and convenient

It can be fixed from top to bottom or from bottom to top without dismantling the steel strip.
Add installation reference surface support on the side of the body.There is a positioning PIN hole at the bottom of the body.

The strength increases and the smoothness improves

Due to the use of aluminum body structure, the strength of the body is significantly increased. Compared with RMH5S/6S, the steel track is embedded in the aluminum body and then ground, thus improving the accuracy of the walking height and straightness to below ± 0.02MM (compared with RMH10/12)

Ordering Method

GRC8 - L10-100 -BC-M20B - C4 -0001

Specification

Spec	Repeatability(mm)		±0.005/0.01
	Ball Screw Lead (mm)		5	10	20
	Maximum Speed (mm/s) ※1		250	500	1000
	Maximum Payload	Horizontal (kg)	50	30	18
		Vertical (kg)	15	8	5
	Rated Thrust (N)		683/1388	341/694	174/347
	Stroke Pitch (mm)※2		50-1050mm/50Pitch
Parts	AC Servo Motor Power (W)		200/400
	Ball Screw Ø (mm)		C7Ø16
	High Rigidity LinearGuide(mm)		Ball Screw Actuator
	Coupling (mm)		10X14
	Home Sensor	Outside	EE-SX672(NPN)

Sensor Layout

※1 Acceleration and deacceleration value is set 0.2 second.

※2 When the stroke is over 600mm, the run-out of the ballscrew will occur. We recommend to low down the working speed under this circumstances. Please refer to P85 for details.

Allowable Overhang

(Unit : mm)

Horizontal Installation		A	B	C
Lead5	20kg	1560	153	237
	35kg	890	81	126
	50kg	550	53	82
Lead10	10kg	1730	286	412
	20kg	839	136	196
	30kg	541	86	124
Lead20	6kg	1213	403	493
	9kg	800	264	323
	18kg	592	194	238

(Unit : mm)

Wall Installation		A	B	C
Lead5	20kg	214	153	1435
	35kg	113	81	845
	50kg	74	53	506
Lead10	10kg	370	286	1400
	20kg	176	136	800
	30kg	112	86	495
Lead20	6kg	444	403	760
	9kg	292	264	277
	18kg	214	194	544

(Unit : mm)

Vertical Installation		A	C
Lead5	10kg	331	331
	15kg	220	220
	-	-	-
Lead10	5kg	589	589
	8kg	368	368
	-	-	-
Lead20	3kg	935	935
	-	-	-
	-	-	-

Static Loading Moment

(Unit : Nm)

MY	318
MP	318
MR	626

*The torque value in the chart indicate the center of gravity.

*Operation life is 10,000km when the product is using under the specified conditions.

*Data information is not for ceiling-mount inverse use. Contact us for the details if you want to apply ceiling-mount inverse usage.

Spec Index of Electric Actuator

Use Where	Driven Mode	Model Specification	Motor Output (w)	Width (mm)	Repeatability (mm)	Ball Screw Spec		Maximum Payload(kg)		Maximum speed (mm/s)*1
Use Where	Driven Mode	Model Specification	Motor Output (w)	Width (mm)	Repeatability (mm)	Outer Diameter （mm）	Lead(mm)	Horizontal	Vertical	Maximum speed (mm/s)*1
Stndard	Ball Screw	GRC 5	100W	54	±0.01	12	2	30	10	100
							5	30	10	250
							10	15	5	500
							20	10	2.5	1000
		GRC 8	200/400W	82	±0.01	16	5	50	15	250
							10	30	8	500
							20	18	3	1000
		GRC 12	400W	120	±0.01	16	5	110	33	250
							10	88	22	500
							20	40	10	1000
							32	30	8	1600
		GRC 15	750W	150	±0.01	20	5	120	50	250
							10	120	40	500
							20	83	25	1000
							40	43	12	2000